m_princip
02-25-2008, 06:40 PM
Everyone,
This is for those that have upgraded to Windows Vista and have found that low and behold the cable will no longer work with Loader 2. It took me a couple of days to figure this out and of course Radio Shack still hasn't responded with a fix for this issue. The drivers at the Radio Shack site and that come with the cable will not work with Vista. Vista will recognize that the cable is there but cannot install the drivers nor download them from the net. At last a fix for this....
Since I use the USB to Serial cable made by Radio Shack to connect my VS Platnum to my laptop or main computer. I thought I'd post this where it could do some good.
PLEASE NOTE: This worked for me. Please don't hold me responsible if it doesn't work. I don't know why it wouldn't but just the same, I do not know your computers configuration and this post is just to help others trying to fix the problem.
1. Download the attached file below called "rshack.zip"
2. Extract them (it will create a folder called "rshack") and copy the rshack folder to the C:\Windows\inf\ folder (I am going to assume the C: drive at this point if you use another drive just change the C: to whatever it is)
NOTE: If your cable is attached see step 3. If your cable is NOT attached, skip to step 4.
3. If you have your cable attached go to the control panel.
Select Hardware and Sound.
Select Device Manager.
In the other devices section you should see something like USB to Serial, Right click and select Update Driver Software.
Select Browse my computer for driver software.
In the dialog box type in the directory you put the files in earlier
(C:\Windows\inf\rshack)
Make sure you have a check mark in check subfolders box.
Click next.
At this point Vista should find the driver files for you.
The driver is not digitally signed so you will get a dialog wanting you to confirm installation of the drivers.
After this completes you are good to go!
You should be done.
4. If you have not attached your cable.
Complete all steps up to and including step 3.
Plug in your cable.
Allow Vista to look for your device...
When it can't find it select other options and then browse my computer for driver files.
Point it to the C:\Windows\inf\rshack folder make sure the check subfolders box is selected.
Click next.
At this point Vista should find the driver files for you.
The driver is not digitally signed so you will get a dialog wanting you to confirm installation of the drivers.
After this completes you are good to go!
Hope this helps everyone dealing with Vista and Loader2 and USB Radio Shack Cable.
This is for those that have upgraded to Windows Vista and have found that low and behold the cable will no longer work with Loader 2. It took me a couple of days to figure this out and of course Radio Shack still hasn't responded with a fix for this issue. The drivers at the Radio Shack site and that come with the cable will not work with Vista. Vista will recognize that the cable is there but cannot install the drivers nor download them from the net. At last a fix for this....
Since I use the USB to Serial cable made by Radio Shack to connect my VS Platnum to my laptop or main computer. I thought I'd post this where it could do some good.
PLEASE NOTE: This worked for me. Please don't hold me responsible if it doesn't work. I don't know why it wouldn't but just the same, I do not know your computers configuration and this post is just to help others trying to fix the problem.
1. Download the attached file below called "rshack.zip"
2. Extract them (it will create a folder called "rshack") and copy the rshack folder to the C:\Windows\inf\ folder (I am going to assume the C: drive at this point if you use another drive just change the C: to whatever it is)
NOTE: If your cable is attached see step 3. If your cable is NOT attached, skip to step 4.
3. If you have your cable attached go to the control panel.
Select Hardware and Sound.
Select Device Manager.
In the other devices section you should see something like USB to Serial, Right click and select Update Driver Software.
Select Browse my computer for driver software.
In the dialog box type in the directory you put the files in earlier
(C:\Windows\inf\rshack)
Make sure you have a check mark in check subfolders box.
Click next.
At this point Vista should find the driver files for you.
The driver is not digitally signed so you will get a dialog wanting you to confirm installation of the drivers.
After this completes you are good to go!
You should be done.
4. If you have not attached your cable.
Complete all steps up to and including step 3.
Plug in your cable.
Allow Vista to look for your device...
When it can't find it select other options and then browse my computer for driver files.
Point it to the C:\Windows\inf\rshack folder make sure the check subfolders box is selected.
Click next.
At this point Vista should find the driver files for you.
The driver is not digitally signed so you will get a dialog wanting you to confirm installation of the drivers.
After this completes you are good to go!
Hope this helps everyone dealing with Vista and Loader2 and USB Radio Shack Cable.